Return to SBM4 Locking Collar

Sort By:: Most Helpful Newest Rating: High to Low Rating: Low to High	Page of 1

0 of 0 people found the following review helpful:

April 6, 2020 Reviewer: Jared from Gilbert, AZ United States   Was this review helpful to you?

0 of 0 people found the following review helpful:

Works, but need longer screws May 7, 2019 Reviewer: Daniel Brown from Terryville , CT United States   Received product quickly, but upon installation the screw for collar was too short. Odin supplies a 6-32 by 7/16 cap screw which only grabbed two treads and immediately stripped out. Replaced with a 6-32x9/16 and worked perfectly, Odin... please include 9/16 screws in the future. Was this review helpful to you?

0 of 0 people found the following review helpful:

Wonderful Product November 22, 2018 Reviewer: Alex E. from STL, MO   Received my locking collar within 3 days, it does it's job and keeps my brace from rotating a lot more than I imagined it would. I wouldn't own an SBM4 without this locking collar. Was this review helpful to you?

0 of 0 people found the following review helpful:

Great product and excellent customer service April 10, 2018 Reviewer: Justin Luy from Memphis, TN United States   I had initially recieved a lemon of the batch which the thread were easily stripped but I was rest assured with the lifetime warranty on their products. They promptly sent me a new product. Was this review helpful to you?

0 of 0 people found the following review helpful:

Confused staff on product info is poor C/S February 19, 2018 Reviewer: Tom from Philadelphia, PA United States   Ordered the SBM4 Locking Collar after calling Odin Works to verify what diameter pistol tubes it was compatible with, the information given was that the SBM4 Locking Collar would work just fine with tubes in the range of 1.185 to 1.25 diameter. Also the website listed that this SBM4 Locking Collar would work with KAK pistol tubes. Well I received the SBM4 Locking Collar a few days after ordering and found it will not work with the KAK pistol tube which has a diameter of 1.25" so I called Odin works and was told by a male employee that I had to clamp down with the supplied screw and it should work. If I had taken his advice I would have damaged the tube as the SBM4 Locking Collar fully closed mic's out at 1.180" which would crush a 1,25" tube. Odin later deleted the paragraph which stated that the clamp will work with KAK tubes from the clamps web page after I contacted them with my complaint. Confused staff on product info would have caused damage if I followed Odin's instructions. Was this review helpful to you?

0 of 0 people found the following review helpful:

Confused Staff on product Info February 13, 2018 Reviewer: Tom from U.S.A   Ordered the SBM4 Locking Collar after calling Odin Works and asking what diameter pistol tubes it was compatible with, the information given was that the SBM4 Locking Collar would work just fine with tubes in the range of 1.185 to 1.25 diameter. Also the website listed that this SBM4 Locking Collar would work with KAK pistol tubes. Well I received the SBM4 Locking Collar a few days after ordering and found it will not work with the KAK pistol tube which has a diameter of 1.25" so I called Odin works and was told by a male employee that I had to clamp it down with the supplied screw and it should work. If I had taken his advice I would have damaged the tube as the SBM4 Locking Collar closed diameter mic's out at 1.180 completely closed. Odin Works also deleted the paragraph which stated that the clamp will work with KAK tubes from the clamps web page. Confused staff on product info is poor customer service. Was this review helpful to you?